Environmental Protection

All Products

Thompson Pump and Mfg.

Trash and Sewage Pump

Thompson Pump’s 8TSC 8-inch multipurpose Enviroprime trash/sewage pump provides flows up to 2,600 gallons per minute and heads up to160 feet. The pump case can clean debris from the impeller or repair wear items in the pump. The priming system prevents product blow-by from being discharged onto the ground or through hoses.

    Gardner Denver Nash

    Vacuum Pump and Compressor

    Gardner Denver Nash’s NASH Vectra XL 750 is a liquid ring vacuum pump and compressor. The pump operates at 28.5 inches HgV, and the compressor operates at 30 PSIG. The device features an o-ring sealing, oil lubrication and single-point inlet and discharge connections. The product is made of 316L stainless steel.



      The Moyno Annihilator is a twin-shaft solids reduction grinder designed for solids reduction and waste conditioning. The device features a counter-rotating hexagonal shaft design, five-tooth steel cutters and a mechanical seal cartridge with stainless-steel sleeves. Various drive, housing, cutter, spacer/cutter and shaft options are available.


        Water Generator

        Munters' H2O LiquidAir is a water-generating solution that captures outside air moisture and converts it into pure drinking water. The device dehumidifies and cools air while it removes moisture. The system uses R-410A refrigerant to help preserve the ozone layer.


          Flow Meter

          McCrometer’s Marsh Multi-Mag Flow Meter features a multi-electrode sensor with an insertion style configuration suitable for hot-tap installation. Multiple electrodes located across the sensor body measure and indicate the average flow rate. The hot tap installation allows the device to be removed and installed in other locations to support temporary measurement needs. The product is available in sizes from 4 to 120 inches.


            Water Purification System

            ELGA’s Purelab Flex water purification system integrates in-hand monitoring and pure water dispensing. The handheld dispenser displays volume and water purity, which allows users to monitor the water purity while dispensing water. The product can be configured with a purification pack and UV lamp to produce Type I, II and III polishing and dispense systems.

              Blue Angel Pumps

              Sump Pumps

              Blue Angel’s sump pumps are designed to detect the presence of water and air in a pump. The devices determine a pump’s cycle time and feature microprocessor-controlled switches with cap switch technology. The switches contain no moving parts and are designed to endure more than 1 million on/off cycles.


                Analog Output Modules

                Acromag’s ES2171 and ES2172 analog output modules provide 16-bit Ethernet-to-voltage or current conversion for control of up to 16 industrial devices. The modules accept Modbus TCP/IP, UDP/IP and i2o peer-to-peer network inputs, and provide high-resolution analog outputs to drive displays, indicators, chart recorders, positioners and actuators. An aluminum enclosure resists 50G shock and 5G vibration. The units are designed to mount on machinery, DIN rails or walls. The industrial-grade specs feature -40 to 75 degrees Celsius operating temperatures.


                  Medical Waste Incinerator

                  Elastec/American Marine’s MediBurn30 portable medical waste incinerator features dual-chamber combustion, under-air technology and modulating burners. The product contains a redesigned electronics suite with a multilingual user interface, and a door lock and sensor to prevent accidents. The 2,440-lb. unit is designed for use in laboratories, small hospitals and medical clinics and disaster relief operations.


                    Cooling System

                    Munters’ Oasis indirect evaporative cooling system uses a corrosion-resistant polymer heat exchanger to produce dry, cool air without refrigeration. Best suited for hot, dry climates, the system treats makeup air for 50 percent less energy and provides cooling energy recovery and winter heat recovery. The product assists in reducing peak demand loads.



                      Munters’ DryCool Standard allows users to control temperature and humidity independently. The product is designed to treat 100 percent makeup air and can work in conjunction with an existing air-conditioning system or energy recovery ventilator. The unit controls humidity on an as-needed basis, when humidity levels exceed setpoint. It has the capacity to process between 1,000 and 16,000 cfm of makeup air.

                        Sierra Instruments

                        Flow Meter System

                        Sierra’s Multi-Trak 670S multi-point mass flow meter system measures mass flow rates in areas that have non-uniform velocity profiles, high turn-down requirements, dirty gas streams and wide temperature ranges. The product uses up to four independent mass flow sensing points to calculate the average gas mass flow velocity. A microprocessor-based human machine interface controls all functions of the system. The sensors are FM, CSA and ATEX certified for hazardous areas, and are CE approved.

                          EXAIR Co.


                          EXAIR’s Heavy Duty Threaded Line Vac Conveyors convert piping to a conveying system for steel shot, metal parts, scrap, and trim bulk materials. Designed for rugged, industrial applications, the device has a hardened alloy construction. The conveyors eject a small amount of compressed air through directed nozzles to produce a vacuum on one end with high output flows on the other.

                            Control Co.

                            Conductivity/TDS/Salinity Meter

                            Control Company’s Traceable Conductivity/TDS/Salinity Meter is equipped with chemical-resistant waterproof ABS plastic housing. The device contains LCD digits and a dual-display that shows readings and temperatures. Temperature compensation allows readings to be automatically referenced to the international standard of 25 degrees Celsius, or the user can set a programmable temperature coefficient.

                              Innovative Pressure Technologies

                              Manifold Valves

                              Innovative Pressure Technologies’ 2-, 3- and 5-way manifold valves are designed to connect system impulse lines and transmitters. The devices combine tee and calibration and isolation valve functions into one valve configuration. Each valve contains bonnet lock pins to prevent accidental loosening.

                                Free e-News Subscription

                                I agree to this site's Privacy Policy