Environmental Protection

All Products


Select Fabricators, Inc.

Select Fabricators Select A Shield

Select-A-Shield

Select-A-Shield

Select-A-Shield RF EMI Shielded tents are used for everything from pre-compliance testing to secure communications. To assure shielding effectiveness during entry and exit, Select Fabricators, Inc. has developed a vestibule for its Select-A-Shield walk-in enclosures. With most walk-in enclosures, opening the door can immediately degrade shielding effectiveness resulting in possible data capture compromise or data corruption. With the addition of the Select-A-Shield vestibule, which is integral to the enclosure, the shielding environment is kept intact for consistent shielding performance.

In a typical 9’ wide, x 12’ length Select-A-Shield tent, the vestibule is situated in the right-hand front corner. 3’ x 4’, in size, the vestibule provides entry for personnel via a separate single door double magnet (patent pending) closure system which opens out. The vestibule has its own separate conductive floor, door,and inner walls apart from the tent itself which allows maximum isolation for continuous testing or examination. The door opening to the main compartment opens inwards, making entry and exit easier.

Select-A-Shield RF EMI shielded enclosures with vestibules typically include a white ESD liner and ventilation. “Ventilation is necessary when people occupy a RF EMI shielded tent”, stated Lynne Woodworth, chief development officer at SELECT, “SELECT’s fan and vent system is RF EMI shielded to preserve the shielding effectiveness of the structure. The white ESD liner not only protects against static, it also helps technicians read and record data against a neutral, brighter background.”

Select-A-Shield RF / EMI enclosures  are constructed with RoHS compliant, durable, lightweight, Silver/Copper/Nickel, Nova Select fabric, SELECT’s proprietary highly conductive material. Shielding effectiveness for a vestibule measures -73 dB with both doors closed at 916 Mhz.  A double wall RF EMI shielding tent with ESD liner yields an average SE of -78 dB average from 150 kHz to 18 GHz without the vestibule.  

“We developed this US-based fabric to yield high conductivity for the widest range of applications,” said Woodworth. “We’ve done everything from die-cut parts to a shielded enclosure large enough to hold a tractor. The possibility to design shielding that assures RF EMI isolation from off-the shelf standard configurations to custom designs is what drives SELECT.”

Select-A-Shield RF EMI products are ideal for numerous applications including wireless device development and testing, secure communications, satellite communications testing and isolation, EMC pre-compliance, medical and aerospace equipment shielding, cellular and computer forensics, and RFID shielding for commercial and industrial settings. Because Select-A-Shield products can be customized to almost any size and option configuration, application suitability is endless.


    Air Cycle Corp.

    Bulk Pickups by Air Cycle

    Bulk Pickups

    Bulk Pickups

    For larger facilities (over 150,000 square feet), Bulk Pickups offered by Air Cycle can provide a cost effective solution for recycling large amounts of intact or crushed lamps, ballasts, batteries, or electronic waste.

    How Does It Work?

    • Request a quote, or schedule a pickup online or by phone (800-909-9709).  Pricing depends on your facility location and quantity of waste picked up.
    • The recycling team will coordinate a pickup date that works best for you.
    • Your packaged waste is picked up and delivered to a certified recycling partner located across the country.
    • Once the waste has been recycled, you will receive a Certificate of Recycling, confirming the proper handling of your waste.

      Air Cycle Corp.

      EnviroPure Food Waste Diversion System by Air Cycle

      EnviroPure Food Waste Diversion System

      EnviroPure Food Waste Diversion System

      The EnviroPure Food Waste Diversion System by Air Cycle is an organic, self-contained, continual feed system that has been designed to transform food waste into a greywater effluent that can be safely disposed of into existing municipal water systems. The system is a great fit for any commercial kitchen operation such as hotels and schools. EnviroPure eliminates transportation costs for food waste, reduces janitorial labor and supply costs, and creates positive environmental impacts.

      EnviroPure handles virtually any type of food waste including vegetables, fruits, meat, fish, poultry, dairy products, bones, shells and pits, with complete decomposition typically occurring within 24 hours. The system creates a positive environmental impact and is low maintenance with no odors, no sludge buildup, and no clean outs.


        Air Cycle Corp.

        Rodale Institute CDS by Air Cycle

        Rodale Institute CDS

        Rodale Institute CDS

        The Rodale Institute CDS by Air Cycle generates sanitizer and detergent from salt, water, and electricity while eliminating costs and the carbon footprint of shipping large quantities of chemicals. The system is recognized by EPA, FDA, and CDC, and produces cleaning solutions on-demand, as-needed. The units are constructed from durable 300 series stainless steel and there are models available for every facility size and application.

        The system has been EPA registered and CDC recognized as a disinfectant, which has been FDA approved for use in food processing environments. It can also be used across several markets such as hospitality, entertainment venues, healthcare, universities/schools, office buildings, agriculture, and in food service and processing.


          Air Cycle Corp.

          EasyPak Pre-Paid Recycling Containers by Air Cycle

          EasyPak Pre-Paid Recycling Containers

          EasyPak Pre-Paid Recycling Containers

          EasyPak Pre-Paid Recycling Containers are the safe and easy way to recycle your facilities’ fluorescent bulbs, batteries, ballasts, and electronics. One price includes everything you need: the UN Certified recycling container, shipping to the recycling center, recycling fees, and certificates of recycling.

          In order to begin using the containers, go to Air Cycle’s website and follow three easy steps. First, you can select the type of contains you’ll need, such as lamp, battery, and electronics recycling containers. You will then receive your selected containers in the mail and can begin filling them with waste. Return the filled containers for recycling when ready. It’s that simple.


            Air Cycle Corp.

            The Bulb Eater by Air Cycle Corp.

            The Bulb Eater

            The Bulb Eater

            The Bulb Eater Lamp Crusher by Air Cycle crushes spent fluorescent lamps of any length into 100% recyclable material while capturing over 99.99% of the vapors released. The system, which is mounted to a 55-gallon container, can hold up to 1350 4-foot fluorescent lamps.

            The lamp crusher unit is equipped with a side-mounted dust filter unit containing the highest quality H.E.P.A. filter available. This works in conjunction with an activated carbon filter located in the steel canister. The activated carbon filter actively captures and neutralizes the mercury vapor released from the lamps during crushing.

            A recent study showed non-detectable levels of escaped mercury vapor even after crushing 1500 lamps. A new safety control panel has also been added, giving the operator added security by monitoring seven aspects of the machine to better ensure operator safety.

            In addition to providing EPA and OSHA compliance, the Bulb Eater Lamp Crusher frees up valuable storage space normally filled with boxes of spent whole lamps, reduces handling and related labor costs, and typically cuts recycling costs by 50% or more.

            The Bulb Eater is capable of crushing straight lamps of any length, U-Tube lamps (Model VRS-U only), and even a 4-foot fluorescent lamp in a single second. The product reduces labor by 20 hours per 1,000 lamps, saves up to 50% on recycling costs, and minimizes storage space by 80%.


              Neptune Chemical Pump Co. Inc.

              Abaque Series Peristaltic Pumps by Neptune Chemical Pump Co.

              Abaque Series Peristaltic Pumps

              Abaque Series Peristaltic Pumps

              Neptune Chemical Pump Co. is pleased to announce the addition of the Abaque Series Peristaltic (Hose) Pump product line to its portfolio for the Americas. All Abaque Series pumps sold in the Americas will now be manufactured and shipped from PSG’s Neptune facility in North Wales, PA. The move is being made to better align the Abaque line with other PSG products and services that address the same primary market segments. The Abaque pumps are still available in 9 different models/sizes—from the AB10 to the AB100—with flow rates ranging from .07 to 211 gpm (.015-48 m3/hr).

              The Abaque Series pumps feature a seal-free design that eliminates leaks and product contamination, which enables them to handle a wide array of challenging pumping applications in the oil and gas, chemical process, industrial and municipal water treatment, paint and coatings, and mining industries. The pumps, which can run in either forward or reverse, are self-priming and offer suction-lift capabilities to 29.5 feet, as well as the ability to run dry continuously without adversely affecting the pump’s performance. Ductile-iron and steel construction enables the pump to offer maximum discharge pressures as high as 217 psi.

              Abaque Series pumps can be ordered as bare-shaft pumps or with a variety of drive options. Standard drive configurations include C-face gear reducer or C-face gear reducer with TEFC, explosion-proof or single-phase motors.


                Fluid Components International

                Fluid Components International (FCI)

                FS10A Analyzer Flow Switch/Monitor

                FS10A Analyzer Flow Switch/Monitor

                Water and wastewater operations and plant engineers in search of a flow switch/monitor to ensure flow to their water or gas sampling systems or analyzers will find their solution in the Model FS10A Analyzer Flow Switch/Monitor from Fluid Components International (FCI). No matter how sophisticated a fluid analyzer system may be, it will be ineffective if a sample flow fails to reach the analyzer sensor. The most advanced systems in the world cannot provide accurate results without a valid fluid sample.  That’s why FCI developed the advanced FS10 Analyzer Flow/Switch Monitor.

                The FS10A Flow Switch/Monitor is designed for use with tubing from 1/8 inch to ½ inch and the electronics may be either integrally mounted or remote mounted from the sensor element.   It is extremely sensitive to low flow rate detection, there are no moving parts to foul or clog, and there are no cavities, orifices, or dead-legs to trap or contaminate samples. 

                FS10A is suitable for application in liquid or gas analyzer sampling systems.  It is small, lightweight, and features a choice of electronic outputs including open collector, relay, and       

                4-20mA outputs.  Limit alarms are user programmable for time delay and/or hysteresis.  An on-board 10-LED array provides at-a-glance visual indication to the user of flow rate and whether the alarm limit has been tripped.   All FS10A set-up parameters can be performed via its two front panel push buttons or via a PC over its RS232C I/O. Its exclusive “learn” mode facilitates easy user set-up of flow range zero and span settings. 

                Water and wastewater end-users and system integrators will find FCI’s FS10A provides an overall solution for sampling system and analyzer flow assurance. With its advanced electronics and reliable thermal dispersion flow sensing technology, it will ensure the highest integrity process analysis without interruption.




                  LiteEarth

                  LiteEarth Capping System

                  LiteEarth Capping System

                  LiteEarth is an impermeable capping system for the long-term cover of landfills, coal ash, gypsum deposits, and land reclamation projects. LiteEarth utilizes proven components and design to save money, resources, time and the environment. The system permanently combines the latest synthetic turf with EPDM geomembrane into a lightweight, single-ply composite. The impermeable EPDM membrane offers flexibility and durability to resist cracking and easily conform to the terrain.

                  Synthetic grass provides natural looking cover 24/7/365 days a year, and eliminates costly and environmentally damaging fertilizers, pesticides, fungicides, and mower exhausts required for natural grass maintenance. The composite is delivered to project site in pre-manufactured size and length specifications, and only layout, positioning, and seaming is necessary on site. This patent pending system is the only EPDM-synthetic grass composite of its kind.


                    Walchem

                    Walchem Opti-Check Fluorometer

                    Opti-Check Fluorometer

                    Opti-Check Fluorometer

                    For years, Walchem has offered the WebMasterONE control in conjunction with Turner Designs Little Dipper online fluorometer, to accurately measure and control the concentration of scale or corrosion inhibitors in cooling tower and boiler applications. Now the Opti-Check fluorometer is available to ensure that the calibration of the online sensor is accurate. A low cost PTSA version, and an affordable PTSA/Fluorescein version, is available.

                    The Opti-Check handheld fluorometer requires low maintenance, is easy to use, and comes in a durable dustproof, watertight (IP 67) package. The product is sensitive to less than 1 ppb of fluorescent dye and provides better control of treatment chemicals.


                      FilterSense

                      The FilterSense Model PM 100 is a multi-channel particulate monitor.

                      Model PM 100

                      Model PM 100

                      htttp://www.filtersense.com


                        Valco Instruments Co. Inc.

                        Model DV22 Mini Diaphragm Valve

                        Model DV22 Mini Diaphragm Valve

                        VICI’s Microvolume Diaphragm Valve by Valco Instuments, Co. Inc. (VICI) is designed for trouble-free use in applications that require minimal maintenance and maximum lifetime, making it the ideal choice for the process industry, automated lab analyzers, and continuous-monitoring environmental analyses. Three configurations are available: a 4 port internal loop sample injector, a 6 port external loop sampling/switching valve, and the industry’s first 10 port multifunctional diaphragm valve.

                        Lifetime for the DV22 can exceed 1,000,000 cycles at ambient temperature/300 psi or 500,000 cycles at 175°C/300 psi. The standard valve is for applications in which the sample is above ambient pressure, but it can also be used with sub-ambient pressures, such as when the sample is pulled through the valve by vacuum.

                        Actuator air (40-50 psi) is supplied to a side port with 10-32 female threads, permitting use of a variety of compression or barbed fittings. A 3-way solenoid is required for actuation, which may be ordered separately.Maintenance procedures are greatly simplified, since the valve is held together by a single screw and locating pins insure proper alignment.


                          Bingham & Taylor

                          Bingham and Taylor Sealed System

                          Valve Box Sealed System

                          Valve Box Sealed System

                          The Sealed System by Bingham & Taylor consists of a Valve Box Stabilizer and a Debris Trap, which are available together, or separately. The Stabilizer has the highest versatility, fitting all round valve box bells and bases, for use with either cast iron or plastic valve boxes. It is highly effective in preventing the intrusion of dirt, backfill, or sand from below.

                          The patented design assures proper alignment of the valve box and protection of the valve. It also assures that all “down” force is transferred to the back filled area, rather than to the buried valve or pipe. It eliminates the need to “block up” the valve box.

                          The Debris Trap component of the Valve Box Sealed System was engineered to eliminate maintenance and service issues caused by debris intrusion through and around the valve box top over time. The Debris Trap design is also responsible for the system being “no vac” because it eliminates the need to vacuum out the box prior to actuating the valve.

                          The Debris Trap is designed to fit domestic and imported valve boxes, both plastic and cast iron. It is manufactured from utility grade ABS plastic, which is ideal for applications that demand high surface hardness, rigidity, impact strength and overall toughness for utility maintenance products.

                          The Bingham & Taylor “No Vac” Debris Traps are manufactured in yellow and black, paintable and markable with standard indelible markers, and are proudly manufactured in the USA.


                            Plasma Etch

                            Plasma Etch Magna Series

                            Magna Series

                            Magna Series

                            Plasma Etch, Inc. has developed a technology called the Magna Series(patent pending) that eliminates the need of CF4 gas that is presently used by printed circuit board manufacturers throughout the world with the use of plasma etching systems for desmear and etchback processing applications.

                            The Magna Series Technology is a great achievement and advancement in the protection of the global environment and preservation of our ozone layer. The new product eliminates the need of CF4 gases, does not require the use of O2 bottles, and uses less power than traditional plasma etching systems that are currently in use.

                            Plasma Etch reports the Magna Series has also set new market standards in several other key areas. The new technology provides faster etch times, lower operating cost, and process uniformity that is not achievable by using existing technologies.


                              General Monitors

                              General Monitors SM100 Sampling Pump Module

                              SM100 Sampling Pump Module

                              SM100 Sampling Pump Module

                              The new SM100 Sampling Pump Module from General Monitors draws combustible or toxic gases at 0.05 to 1 LPM from monitored areas to a gas detector, making it easier and more cost effective to measure potentially hazardous gases in areas that are too remote, inaccessible, cold, hot, or wet for direct sensor monitoring.

                              The user-friendly SM100 Sampling Pump Module supplies gas for up to three gas detectors, which is useful for monitoring multiple gases in a single line. The SM100 features a low flow indicator that informs the end user if flow is insufficient for gas detection. The product also includes a trouble relay that provides a local signal indication of the low flow condition.

                              The SM100 Sampling Pump Module reduces plant operating costs by simplifying operation and maintenance. The product’s rugged design and 316-stainless steel construction make it suitable for gas detection service in a variety of harsh industrial environments. Areas particularly suited for monitoring with the SM100 include ducts carrying combustible or toxic gas, wet wells, sewage dryers, printing drying ovens, and storage tanks.

                              The SM100 is available in two configurations, an aspirated model that is used with a compressed air source and a DC pump module. The aspirated model is designed for use with instrument grade aspirator air, up to a max aspirator pressure of 30 psig (206 kPa).

                              The SM100 operates at a wide temperature range of -4°F to +131°F (-20°C to +55°C) and at a humidity range of 15-95% RH, non-condensing. Its enclosure is C-UL-US approved and designed for use in Class I, Div. 1, Groups A, B, C & D.


                                Free e-News Subscription

                                I agree to this site's Privacy Policy