Environmental Protection

Browse by Company


  • Fluid Components International

Fluid Components International

The new ST102A Air/Gas Thermal Mass Flow Meter features an advanced dual-element averaging system, improving installation repeatability and accuracy for larger diameter pipes and ducts.

ST102A Air/Gas Thermal Mass Flow Meter

ST102A Air/Gas Thermal Mass Flow Meter

The new ST102A Air/Gas Thermal Mass Flow Meter features an advanced dual-element averaging system, improving installation repeatability and accuracy for larger diameter pipes and ducts.

Flow measurement applications involving line sizes 12 inches or greater can realize improved installation accuracy and repeatability by averaging the flow rates of two elements. Distorted, swirling and non-repeatable flow profiles can result in decreased accuracy of single point meters. It is often impractical or impossible to provide the required straight-run for a fully developed flow profile in large lines.

The transmitter electronics average the input from two independent flow elements into a single output. Each flow element can be independently configured for insertion length and process connection to allow installation flexibility. One flow element can be integral with the flow transmitter, or both can be configured as remote for easier access and visibility to the digital display/optical four button user interface. The flow transmitter also provides independent information for each flow element, saving time when performing service checks.


    Fluid Components International

    FS10A Analyzer Flow Switch/Monitor

    FS10A Analyzer Flow Switch/Monitor

    FS10A Analyzer Flow Switch/Monitor

    Process or analytical instrumentation engineers looking for a flow verification solution for their process analyzer sampling systems, the Model FS10A Analyzer Flow Switch/Monitor from Fluid Components International (FCI) meets the requirements for Safety Integrity Level (SIL) 2 compliant service.

    FCI’s SIL 2 compliance rating for the FS10A Analyzer Flow Switch/Monitor has been documented in a failure analysis report with FMEDA techniques by the accredited certification body exida.  The FS10A has been classified as a Type B subsystem in accordance to IEC 61508-1 with a hardware failure tolerance of 0.  

    The product ensures continuous reliability and requires virtually no maintenance, featuring a precision flow sensor element with no moving parts to foul, clog, or maintain. Unlike alternative technologies, such as magnetic floats, capillary bypass, or rotameters, the FS10A has no cavities, orifices, or dead-legs that can trap fluids and lead to contaminated samples, which preserves sample integrity and provides faster system sampling times.

    The monitor is ideal for use with nearly all types of process and emissions sampling systems, including gas chromatographs (GCs), mass spectrometers, optical spectrometers, photometers, and others. 

    The FS10A Analyzer Flow Switch/Monitor outputs include a 1A relay settable for NO or NC operation and with user-settable for failsafe, hysteresis and/or time delay, and a 4-20mA analog output for trending. In addition to SIL 2 compliance, agency approvals for the FS10A Analyzer Flow Switch/Monitor include FM, FMc, ATEX and IECEx for hazardous location installations.


      Fluid Components International

      FCI ST100

      ST100

      ST100

      The ST100 Series Flow Meter sets a new industry benchmark in process and plant air/gas flow measurement, delivering unsurpassed adaptability and value to meet plant gas flow measurement applications for today and tomorrow.

      The ST100 Flow Meter’s graphical, multivariable, backlit LCD display/readout brings new meaning to the term “process information”. It provides the industry’s most comprehensive information with continuous display of all process measurements and alarm status, and the ability to interrogate for service diagnostics.

      The user-friendly ST100 stores up to five unique calibration groups to accommodate broad flow ranges, differing mixtures of the same gas and multiple gases, and obtains up to 1000:1 turndown.  An optional, patent-pending SpectraCal Gas Equivalency calibration method lets users select and switch between 10 common gases. An on-board data logger with an easily accessible, removable 2-GB micro-SD memory card capable of storing 21 million readings comes standard.

      The ST100 offers three different types of flow sensors to best match user applications.  The fast-response FPC-style is a fast response features an integral flow conditioner and protective shroud optimized for compressed air and clean gas applications. The fast-response, general purpose FP-style features a protective shroud and is the sensor used with FCI’s VeriCal in-situ calibration option.  For wet or dirty gases, or erratic flows, the unshrouded S-style facilitates easy cleaning and provides a smoothed response.

      The ST100 can be calibrated to measure virtually any process gas, including wet gas, mixed gases and dirty gases.  The basic insertion style air/gas meter features a thermal flow sensing element that measures flow from 0.25 to 1000 SFPS (0.07 NMPS to 305 NMPS) with accuracy of  ±0.75 percent of reading, ±0.5 percent of full scale.  

      Designed for rugged industrial processes and plants, ST100 Flow Meters include service up to 850ºF and are available with both integral and remote (up to 1000 feet) electronics versions. The ST100 is agency approved for hazardous environments, including the entire instrument, the transmitter and the rugged, NEMA 4X/IP67 rated enclosure.  Instrument approvals in addition to ATEX and IECEx include FM and FMc.


        Fluid Components International

        Fluid Components International (FCI)

        FS10A Analyzer Flow Switch/Monitor

        FS10A Analyzer Flow Switch/Monitor

        Water and wastewater operations and plant engineers in search of a flow switch/monitor to ensure flow to their water or gas sampling systems or analyzers will find their solution in the Model FS10A Analyzer Flow Switch/Monitor from Fluid Components International (FCI). No matter how sophisticated a fluid analyzer system may be, it will be ineffective if a sample flow fails to reach the analyzer sensor. The most advanced systems in the world cannot provide accurate results without a valid fluid sample.  That’s why FCI developed the advanced FS10 Analyzer Flow/Switch Monitor.

        The FS10A Flow Switch/Monitor is designed for use with tubing from 1/8 inch to ½ inch and the electronics may be either integrally mounted or remote mounted from the sensor element.   It is extremely sensitive to low flow rate detection, there are no moving parts to foul or clog, and there are no cavities, orifices, or dead-legs to trap or contaminate samples. 

        FS10A is suitable for application in liquid or gas analyzer sampling systems.  It is small, lightweight, and features a choice of electronic outputs including open collector, relay, and       

        4-20mA outputs.  Limit alarms are user programmable for time delay and/or hysteresis.  An on-board 10-LED array provides at-a-glance visual indication to the user of flow rate and whether the alarm limit has been tripped.   All FS10A set-up parameters can be performed via its two front panel push buttons or via a PC over its RS232C I/O. Its exclusive “learn” mode facilitates easy user set-up of flow range zero and span settings. 

        Water and wastewater end-users and system integrators will find FCI’s FS10A provides an overall solution for sampling system and analyzer flow assurance. With its advanced electronics and reliable thermal dispersion flow sensing technology, it will ensure the highest integrity process analysis without interruption.


          Fluid Components International

          ST100 AirGas Flow Meter

          The ST100 Series Thermal Mass Air/Gas Flow Meter from Fluid Components International (FCI) is available in a remote mountable configuration, for applications in hazardous areas or hard-to-reach locations. Its remote mount transmitter, with optional digital display, can be mounted up to 1000 feet (300 meters) away from the flow sensor using interconnecting cable. It measures, displays and transmits the industry’s most extensive array of parameters. It is available with 4-20 mA analog, frequency/pulse, alarm relays or digital bus communications such as HART, Fieldbus, Profibus or Modbus. The ST100 Flow Meter features a unique graphical, multivariable, backlit LCD display/readout that brings new meaning to the term “process information”. The standard on-board data logger features a removable 2-GB micro-SD memory card capable of storing 21 million readings.

            Fluid Components International

            FlexSwitch FLT93 Pump Protection Flow Switch

            The FlexSwitch FLT93 Pump Protection Flow Switch reduces pump repair and extends pumplife by detecting dry running conditions caused by irregular liquid flows or slurries. It monitors the flow and temperature of liquids, gases, slurries, syrups, lubricants, coolants and more.  It is ideal for pump wet/dry detection, where sudden, unexpected reductions in media flow rates may leave pumps vulnerable to over-heating conditions that can result in bearing or seal damage that require major repairs or shorten their useful life. It also offers a highly robust scheme for pump protection with its dual alarm capability and  features a wide set-point range, which varies according to service media (liquid, gas or foam), beginning from 0.01 to 3 SFPS (0.003 to 0.9 SMPS) in water-based liquids. 

              Fluid Components International

              Fluid_Components_Greenhouse_Gas_Flow_Meter

              Greenhouse Gas Flow Meter

              The ST51 Mass Flow Meter from Fluid Components International comes with stringent safety approvals that include FM, CSA/CRN, Class 1, Div 1, Groups B, C, D and Class 1, Div II, Groups A-D. The meter is ideal for measuring methane and other combustible greenhouse gases. It is an easy-to-install explosion-proof instrument and requires virtually no maintenance. It also features a no-moving parts design and operates over a wide flow range with low-flow sensitivity.

                Fluid Components International

                Flow_Level_Temperature_Switch

                Flow/Level/Temperature Switch

                The FlexSwitch FLT93S Flow/Level/Temperature Switch from Fluid Components International (FCI) performs monitoring, controlling and alarming of flow rates or levels of critical fluids. The switch is a dual-function, insertion-style instrument that offers either flow/temperature sensing or level/temperature sensing in a single device. The company says a single FLT measures and monitors flow or level and temperature simultaneously with excellent accuracy and reliability. Dual 6A relay outputs are standard and are assignable to flow, level or temperature.

                  Fluid Components International

                  Thermal Mass Flow Meter

                  The new ST50 Remote Mount Flow Meter from Fluid Components International features an intelligent, no-moving parts thermal mass flow sensor design. It measures air flow from 1 to 125 SFPS, nitrogen from 1 to 150 SFPS, and compressed air from 4 to 400 SFPS. Accuracy is +1% of reading, +0.5% of full scale, with repeatability of +0.5% of reading. This meter is designed to work in crowded equipment or hazardous plant areas where explosives, flammable, or toxic gases may be present.

                    Fluid Components International

                    Thermal Mass Flow Meter

                    The new ST50 Remote Mount Flow Meter from Fluid Components International features an intelligent, no-moving parts thermal mass flow sensor design. It measures air flow from 1 to 125 SFPS, nitrogen from 1 to 150 SFPS, and compressed air from 4 to 400 SFPS. Accuracy is +1% of reading, +0.5% of full scale, with repeatability of +0.5% of reading. This meter is designed to work in crowded equipment or hazardous plant areas where explosives, flammable, or toxic gases may be present.

                      Free e-News Subscription

                      I agree to this site's Privacy Policy